Specializing in fiberglass repair, gelcoat color matching, and marine electrical for skiffs, bay boats, and center consoles in Citrus County, FL and surrounding areas. Straightforward work, done right, and backed up personally.
I focus on boats running the backwaters, oyster bars, and shallow flats of the Nature Coast—flats skiffs, bay boats, and center consoles, though I gladly work on any vessel.
Having spent nearly 2 decades maintaining and repairing boats up and down the East Coast and Florida's Gulf Coast, I know what holds up to water, sun, and vibration over time. Whether it's fixing oyster bar scratches and gouges on the chine or rebuilding an old dash for clean flush-mount electronics, the goal is simple: durable work that puts your boat back in service and keeps it there.
Proven composite standards built to meet the conditions of local waters so your hull stands up to real-world use.
From the shallow backwaters of Ozello and Crystal River to the open Gulf, every repair is built to withstand real-world use.
I provide dedicated composite repairs, gelcoat restoration, and 12V electrical systems for boats that work and play hard on the water.
Shallow backwaters mean encounters with oyster bars, limestone rock, and trailer impacts. You can do a rock-solid structural repair, but if the finish doesn't look like the damage was never there, that's all anyone's ever going to notice. I grind out damaged material, rebuild the structural glass backing with proper multi-axial cloth, and pair it with precision optical color matching so your finish blends seamlessly back into the hull.
Decks require both aesthetic continuity and dependable footing. I match or take impressions of your original molded non-skid—including diamond and pyramid textures—to create flexible molds that duplicate the factory pattern using color-matched gelcoat.
When upgrading to modern electronics, I bevel, core, and flush-glass old analog gauge holes, speaker openings, and outdated GPS cutouts. This creates a solid, uniform dash surface ready to receive new flush-mount displays or custom switch panels.
For vessels suffering from water-compromised wood cores, I remove degraded core material and rebuild transoms, stringers, and bulkheads using high-density composite core materials—including Coosa, Mamba board, and Divinycell—paired with multi-axial fiberglass laminates for long-term structural integrity.
Reliable power on the water is essential. I install clean, dependable 12V, 24V, and 36V LiFePO4 lithium battery configurations for trolling motors, along with onboard smart charging, clean switch panels, and marine-grade tinned copper wiring with adhesive-lined heat shrink connections.
Measuring your hull's actual color instead of guessing from a factory code, pairing spectrophotometer scanning with careful hand-tinting so repairs blend cleanly into weathered fiberglass.
“You can do the strongest structural fiberglass repair in the world, but if the finish doesn’t look like the damage was never there, that’s all anyone is ever going to see. That’s why I treat the cosmetic match with the exact same standard as the composite layup underneath—so the repair blends cleanly under direct sunlight.”
Ordering gelcoat mixed to an original factory color code often presents real challenges. Even well-maintained boats naturally drift over time due to UV exposure, ambient weathering, and resin aging. A factory-mixed can reflects how the hull looked on day one at the manufacturer, not how it appears on your hull today.
On top of the matching issue, factory gelcoat suppliers typically enforce minimum order sizes—usually 1 quart ($200 to $300) or a full gallon ($350 to $600). For a small chip, screw hole, or oyster scratch, you end up paying for costly surplus material that may not accurately match your boat's current aged finish anyway.
I formulate in small, repair-appropriate quantities. You receive an optical match tailored directly to the current state of your hull without paying for gallons of unneeded material.
Color matching aged gelcoat isn't guesswork or holding up paint chips. It's a combination of optical measurement and careful hand-tinting.
I use a precision spectrophotometer that projects a calibrated full-spectrum light source onto the gelcoat surface. It measures reflected wavelengths across the visible spectrum (400–700nm), translating the hull’s unique color into exact numerical CIE L*a*b* coordinates.
No aged boat hull has a single uniform color. Microscopic wear, differing angles of sun exposure, and variable thickness create slight localized shifts. I take a series of spectral measurements around the repair site and mathematically average them to produce a true target color profile.
Using the spectrometer's Lab target data as a guide, the initial color batch is tinted by hand and eye using raw pigments. Combining digital measurement with precision hand-tinting experience ensures the base tones, saturation, and undertones align properly.
Gelcoat changes shade when it cures with MEKP catalyst used to harden the gelcoat. I catalyze and fully cure test sample tabs, sand and buff them, and re-scan the cured specimen with the spectrometer. I then compare your hull scans, tweak pigments and repeat until the cured specimen matches the hull.
Delta E (ΔE) is the internationally recognized metric used to calculate the visual distance between two colors. A ΔE of 1.0 is widely recognized as the threshold below which two adjoining colors become virtually imperceptible to the unaided human eye.
While standard gelcoat work can often result in ΔE values between 2.0 and 4.0 (which leave noticeable patch outlines in bright daylight), my target for custom matches is ΔE of 0.50 to 0.60. At that standard, when properly prepped, sprayed, and polished, the repair blends into the surrounding hull under natural sunlight.
No service manager, no run around, just solid work on a realistic schedule.
I run Black Creek Boatworks with a simple philosophy: do the job right, use proven marine materials, and personally stand behind every project.
Having spent nearly 2 decades maintaining and repairing boats up and down the East Coast and Florida's Gulf Coast, I know what holds up to salt water, sun, and vibration. Now based on Florida's Nature Coast, I apply those same standards to shallow-water skiffs, bay boats, center consoles, and recreational craft throughout Citrus County, FL and surrounding areas.
When you call, text photos of damage, or drop off your boat, you deal directly with the person doing the grinding, glassing, and wiring. No middleman, no commercial yard runaround—just solid work done on a realistic schedule.
Because I run Black Creek Boatworks as a solo operator in the shop or on a hull, photos and details sent via text get the fastest turnaround. Choose the contact method that works best for you:
Tap below to open your phone's messages with a pre-formatted template. Snap clear photos of the damage or project area and send.
Prefer to talk through the job first? Call the shop line directly. If I'm grinding fiberglass, spraying gel, or laying up cloth, please leave a voicemail.
Working from a desktop or prefer email correspondence? Click below to open and submit the project inquiry form.
Fill in what you know and I will review and follow up with you directly.